Cabinet Hardware Jig

Average Review (15):
     

Install Knobs and Pulls with Easy, Repeatable Accuracy

  • Adjustable guides for accurate hole placement
  • Built-in measuring scales for repeatable results 
  • Versatile for mounting single and multi-hole knobs
  • Adjustable edge guide for easy positioning 
  • Strong, lightweight materials for easy handling 
  • Durable hardened-steel drill guides

$24.99 USD

ITEM No.: KHI-PULL

Add to Cart

Description

The Kreg Cabinet Hardware Jig takes the guesswork out of installing cabinet knobs and pulls. The moveable edge guide and measuring scales make it easy to position knobs precisely, while adjustable drill guides ensure straight holes for perfect knob and pull positioning every time. Perfect for new construction and for refreshing entire rooms.

Whether you're updating your cabinets or building a project from scratch, adding hardware like knobs and pulls is often one of the final steps – and one of the most intimidating. Drill the holes incorrectly, and it can be very difficult to correct the mistake. The Cabinet Hardware Jig takes all the guesswork out of the process by allowing you to drill straight, accurately positioned holes every time, so you'll know that every piece of hardware is positioned correctly and consistently. 

The Cabinet Hardware Jig features moveable, hardened-steel drill guides that lock into place to align with common hole-spacing measurements for cabinet knobs and pulls. This allows you to confidently drill straight, accurately positioned holes. A moveable edge guide and built-in measuring scales (in imperial and metric) ensure that those holes will be positioned where you want it every time, which means you can drill as many holes as you need without the uncertainty and potential mistakes that can come with measuring and marking every one.

The Cabinet Hardware Jig is designed to be intuitive for beginners to use, but robust enough for professionals. All you need is a drill and a 3/16" (5 mm) bit, and the ability to set the jig to match your hardware and the position where you want it to go. Durable polymer construction makes the jig tough but light, and hardened-steel drill guides ensure that you’ll get straight, accurate holes – whether you’re drilling one, a few or hundreds. 

NOTE: 3/16" (5 mm) drill bit required – does not come included.

Specs

Construction

Durable polymer

Drill Guides

Two movable 3/16" (4.5mm) guides with locking nuts

Drill Guide Material

Hardened Steel

Drill Guide Spacing

21/2", 3", 31/2", 4", 41/2", 5"
and 64 mm, 96 mm, 128 mm (2.5", 3.77", 5.03")

Edge Guide to Hole-Centre Spacing

1" to 5" (25 mm-127 mm)

Measuring Scales

Imperial and Metric

In the Box

(1) jig base
(1) edge guide
(2) drill guides with knurled nuts
(2) non-slip pads
(2) T-knobs and bolts
owner’s manual 

Notice

Proposition 65

Manual North American Manual
Global Manual

Reviews for "Cabinet Hardware Jig"

Average Review:
     

Too Small

Will not work on pulls over 5" wide. Just wasted my time and money on this.

     

By John Naugle

March 14, 2020

Too SMALL!!!

This is fine for small drawers less than 5" high, but anything bigger & you have to build a gig like a 1"X 5" L lip to place against this unit. Would it really be that much more expensive to make this a few inches bigger, or have a piece to add onto it for larger drawers and handles?

     

By Mike Graziano

December 2, 2019

Could be much better

Great for aligning cabinet hardware shorter than a 5" span from the top of the jig. Anything longer and you need to remove the piece that aligns with the outer edge of the door or drawer, so for deep drawers that you want to center hardware on, this becomes an issue. This is especially an issue because the back of the jig isn't smooth, therefore when clamped to the cabinet, a honeycomb type of mark from the mold extrusion is left on the cabinet, and can been seen at the right angle. Be careful if you do need to remove this piece for deeper drawers and use a scrap piece of cardboard.

     

By Mike Allen

October 24, 2019

Wonderful jig

We do a lot of cabinet installations and this jig has made handle installation easier. We would love to see a longer and deeper version to accommodate an 8 in handle and deeper drawers.

     

By Jennifer Eiken

September 25, 2019

Needs Other drill bit guide sizes

This seems to work really well, but I agree with most, there should be other drill bit sizes since not all hardware uses the same size of screws (3/16). I think offering other sizes as accessories you can purchase in addition would be a great idea.

     

By Jason Brady

May 24, 2019

Read more reviews

Get Inspired

This website uses first party and third party cookies to improve your experience and anonymously track site visits. By visiting this website, you opt-in to the use of cookies. OK